Troubleshooting The vMotion migration failed because the ESX host were not able to connect over the vMotion network.

Hi All,

Today I will take you thought the troubleshooting for vMotion using CLI, If you have not done network troubleshooting on esx host you will find some really good esxi commands on this post. And if you are using a converged infrastructure its important to understand end to end connectivity especially if you have different vlans for each service like vMotion FT, Management traffic and VM-Traffic.

I build a brand new Data Center and after configuring the dv switch I decided to test the vMotion first and this is the error I saw on the first attempt the vm was stuck at 14 % and after a while it gave the below error message.

as shown below:

vmotion error_task

 

Migrate virtual machine error message

vmotion error

If you read the above error message you will find the IP’s of the host which I am migrating from and to.

for example lets consider the below two host this troubleshooting is done on esx-02. vmnic2 is FT vmnic3 is vMotion so I am comparing the mac address of booth the host on the ucs service profile to compare tht the vnic template has the right mac address and if they are connected to the right vlan. Continue reading “Troubleshooting The vMotion migration failed because the ESX host were not able to connect over the vMotion network.”

Cisco UCS Firmware Overview

Hello Everyone,

Cisco has recently launched a lot of  Firmware for CISCO UCS, it is becoming rather hard to keep up with the new release. We had 5 New Release in Version 2.2 starting from 2.2.(1b),  2.2.(1c), 2.2.(1d),  2.2.(1e), 2.2.(2c).

The good thing is, in every release CISCO  is adding some good features. In one of  the release 2.2.(1d) they have introduced boot from SD, FlexFlash, this option was not available on the older versions of  UCS Manager.

If you are intreasted in this, and want to find how you can boot the ESXi or any other OS off the Secure Digital (SD)  FlexFlash  and how this can be implemented do check  my post  here: Cisco UCS FlexFlash Configuration of Secure Digital (SD) Card

So, for the newbee  to Cisco UCS,  its confusing about the firmware. In this post I am trying to clarify few aspects of this, feel free to post comment below if you have any questions and I will get back to you.

The CISCO UCS firmware is bundled into two packages as given below:

ucs_firmware

 

1. Infrastructure Firmware

In Infrastructure Software firmware we update the firmware of the following

  • Cisco UCS Manager software
  •  Kernel and system firmware for the fabric interconnects
  •  I/O module firmware

2. Server Firmware

Cisco UCS B-Series Blade Server Software Bundle

  • CIMC firmware
  • BIOS firmware
  • Adapter firmware
  • Board controller firmware
  • Third-party firmware images required by the new server

This also includes the firmware of Adapter, BIOSFC Adapters,  HBA Option ROM, Storage, Controller, Local Disk

Cisco UCS C-Series Rack-Mount UCS-Managed Server Software

  • CIMC firmware
  • BIOS firmware
  • Adapter firmware
  • Board controller firmware
  • Third-party firmware images required by the new server

As most of you might be aware the UCS manager is the GUI Java based which allows you to fully manage the CISCO Unified Computing System.

Note I have noticed that the Java version  7 update 40 is only compatible with the UCS Manager. 

So, where does the UCS Manager run ?

This was one of my first questions, Well the Software of the UCS Manager runs on the FI ( Fabric Interconnect 62xx) as we have a pair of Fabric Interconnect it has got resilience.

The UCS System is designed to be highly scalable and available, so upgrading the firmware should not bring any outage to the environment. However Cisco still suggests to arrange a Change windows and get this done out of hours or the quite period of your business.

This UCS Manager is bundled in the Infrastructure Firmware Software along with the Kernal update of the FI which is the NXOS, Finally we have the I/O Module firmware which is a part of the Infrastructure firmware software too.

The Other Bundle is the Server Firmware which has the firmware for BIOS, the Blades, Adapter, Board controller etc.

If you want to learn more about the process of doing a Firmware update please checkout my link CISCO UCS Firmware Update Process

Hope this information is useful, feel free to comment.